Showing all 37 results

  • AutoSET FD Finish

    by ccadmin
    Read more

    AutoSET FD Finish

    AutoSET FD Finish is a quick-drying, high gloss modified alkyd-acrylic enamel especially for OEM and refinish industries.

    Category:
  • AutoSET O P Brown Primer

    by ccadmin
    Read more

    AutoSET O P Brown Primer

    AutoSET O P brown Primer is a modified fast-drying alkyd undercoat for especially OEM and refinish industries. It is typically in brown shade.

    Category:
  • AutoSET Primer 1150 Series

    by ccadmin
    Read more

    AutoSET Primer 1150 Series

    AutoSET Primer Series is based on fast-drying technology. It is recommended for high-end applications were tough and promising properties required.

    Category:
  • Cylcoaliphatic amine cured novalac finish

    by ccadmin
    Read more

    Cylcoaliphatic amine cured novalac finish

    This Novalac coating is a two-component glass flake reinforced epoxy coating designed to withstand the high temperatures of hot steel structures while protecting against corrosion. This epoxy composite coating withstands continuous temperatures up to 250°C and peak temperatures as high as 300°C.

    Category:
  • Epoxy AL Mastic

    by ccadmin
    Read more

    Epoxy AL Mastic

    Aluminum-pigmented, low-stress, high-solids mastic with outstanding performance properties and proven field history. It was the pioneer mastic coating in a number of industrial markets and today still provides unmatched levels of barrier protection and corrosion resistance over existing finishes and rusted or SSPC-SP2 or SP3-cleaned steel.

    Category:
  • Epoxy coal tar Finish

    by ccadmin
    Read more

    Epoxy coal tar Finish

    Renowned high build coal tar epoxy polyamide for protection of steel and concrete in single or two-coat applications in a broad variety of aggressive industrial applications.

    Category:
  • Epoxy DTM Finish

    by ccadmin
    Read more

    Epoxy DTM Finish

    DTM is a polyamide curing, high solids epoxy paint. It forms a hard and tough coating, has good wetting properties and cures at low temperatures.

    Category:
  • Epoxy GF Finish

    by ccadmin
    Read more

    Epoxy GF Finish

    A glass-reinforced chemically resistant epoxy coating with wide versatility in all industrial markets. It is self-priming. Glass reinforcement improves internal film strength, hardness, impact, and abrasion resistance. It is often used in severe service (above or below the waterline) in marine applications where these resistance qualities are desired.

    Category:
  • Epoxy HB Finish

    by ccadmin
    Read more

    Epoxy HB Finish

    A combination of epoxy and polyamide resins with selected pigments designed specifically as a high chemical and corrosion resistance.

    Category:
  • Epoxy Mastic

    by ccadmin
    Read more

    Epoxy Mastic

    This is a two-component epoxy mastic coating for repair and maintenance. The product is surface tolerant, high solids, high build product. Specially designed for areas where optimum surface preparation is not possible or desired. Provides long-lasting protection in environments with high corrosivity.

    Category:
  • Epoxy Micaceous Coating

    by ccadmin
    Read more

    Epoxy Micaceous Coating

    Epoxy Micaceous Coating is a low VOC, high solids, high build epoxy with pigmented with MIO to provide improved overcoating properties, better facilitating application in the fabrication shop. A range of anticorrosive coating systems in a wide range of aggressive environments.

    Category:
  • Epoxy Novolac Finish

    by ccadmin
    Read more

    Epoxy Novolac Finish

    It is an amine adduct cured, phenolic epoxy (novolac) coating with very good adhesion and excellent chemical and high-temperature resistance.

    Category:
  • Epoxy Novolac HB Finish

    by ccadmin
    Read more

    Epoxy Novolac HB Finish

    Single-coat, airless-applied, ultra-high build coating for use on steel and concrete substrates subject to aggressive chemical exposure. Provides enhanced chemical protection for a broader and more concentrated range of acids.

    Category:
  • Epoxy phenalkamine Mastic

    by ccadmin
    Read more

    Epoxy phenalkamine Mastic

    This is a two-component phenylamine cured epoxy mastic coating with high volume solids. It is surface tolerant and fast-drying and can be used as a primer or mid-coat for long-lasting protection in atmospheric environments.

    Category:
  • Epoxy Primer System

    by ccadmin
    Read more

    Epoxy Primer System

    It is a two-component, polyamine adduct cured epoxy primer pigmented with anti-corrosive zinc phosphate and Zinc Chrome. Offers excellent resistance to corrosion and exceptional adhesion to ferrous substrates. Comply with the requirements of BS5493.

    Category:
  • Epoxy Solvent free GF

    by ccadmin
    Read more

    Epoxy Solvent free GF

    Solvent-Free GF is a solvent-free, two-component, high-build, polyamine adduct cured glass flake containing epoxy paint, which cures to a hard and tough coating with good resistance to abrasion, seawater, and freshwater.

    Category:
  • Epoxy topcoat Finish

    by ccadmin
    Read more

    Epoxy topcoat Finish

    This is a two-component polyamide cured epoxy glossy finish for decorative purposes. It is high end and a fast-drying finish.

    Category:
  • Epoxy Zinc HB Primer

    by ccadmin
    Read more

    Epoxy Zinc HB Primer

    A two-component, high solids, low VOC, epoxy zinc phosphate/micaceous iron oxide primer offering excellent barrier protection, low-temperature cure, and rapid overcoating properties.

    Category:
  • Hammer Finish

    by ccadmin
    Read more

    Hammer Finish

    Hammertone paint is a quick-drying, hammer-like finish paint. It gives an excellent aesthetic glossy hammer look.

  • HR Al 250°C

    by ccadmin
    Read more

    HR Al 250°C

    Air-dried coating suitable for high-temperature exposures up to 273°C. Air-drying characteristics allow for faster handling of in-shop applications than with other high-temperature coatings. Heat cure above 149°C is acceptable and will impart added strength and integrity to the coating.

    Category:
  • HR Al 400°C

    by ccadmin
    Read more

    HR Al 400°C

    HR Al 400 is a heat resistant aluminum pigmented polysiloxane paint that cures to a hard film at ambient conditions. Air-dried coating suitable for high-temperature exposures up to 435°C.

    Category:
  • HR Al 600°C

    by ccadmin
    Read more

    HR Al 600°C

    High-performance finish for areas exposed to extreme temperatures. Suitable for service from 204°C-640°C with anti-corrosive advancement.

    Category:
  • HR Matt

    by ccadmin
    Read more

    HR Matt

    Air-dried coating available in matt colors and suitable for high-temperature exposures up to 500°C. The resulting film provides an outstanding barrier against corrosives and harsh exposures typically seen in elevated temperature environments.

    Category:
  • Hybrid Epoxy Zinc rich Primer

    by ccadmin
    Read more

    Hybrid Epoxy Zinc rich Primer

    It is a high performance two-component zinc-rich epoxy primer where extended durability and excellent corrosion protection are required.It is come up with different zinc percentage. Complies with SSPC-Paint 20 level 2 and ISO 12944.5

    Category:
  • Inorganic Zinc Ethyl Silicate Primer/finish-Inorganosil

    by ccadmin
    Read more

    Inorganic Zinc Ethyl Silicate Primer/finish-Inorganosil

    This Primer/finish is designed to withstand high temperatures and provide good corrosion protection. It has been specifically designed for use on areas that operate at temperatures above 120°C and is resistant to continuous high temperatures up to 540 °C

    Category:
  • PU Finish

    by ccadmin
    Read more

    PU Finish

    Thin film, high gloss finish with exceptional weathering performance characteristics. Used extensively in virtually all industrial markets, It provides a smooth, durable finish that has superior resistance to corrosion, abrasion, and chemical exposure.

    Category:
  • PU HB Finish

    by ccadmin
    Read more

    PU HB Finish

    Two-component, high solids acrylic aliphatic polyurethane finish. Finish coat for (anti-corrosive) coating systems on steel and concrete structures in atmospheric exposure conditions.

    Category:
  • PU HS DTM Finish

    by ccadmin
    Read more

    PU HS DTM Finish

    A two-component, DTM urethane mastic, acrylic polyurethane finish providing anti-corrosion barrier protection and long term re-coatability.

    Category:
  • SafeX Premium Finish

    by ccadmin
    Read more

    SafeX Premium Finish

    SafeX series is a water reducible alkyd enamel. This product has an excellent balance of fast dry, tough film properties and economical and can be applied to properly prepared metal substrates. This material is formulated to meet strict air quality regulations.

    Category:
  • SafeX Primer

    by ccadmin
    Read more

    SafeX Primer

    SafeX series is a water reducible alkyd primer. This product has an excellent balance of fast dry, tough film properties and economy and can be applied to properly prepared metal substrates. This material is formulated to meet strict air quality regulations.

    Category:
  • Stipple Finish

    by ccadmin
    Read more

    Stipple Finish

    Stipple paint is a solvent-based powder coating effect paint. It gives a fine glossy texture effect with an aesthetic finish.

  • SynPURE DTM Finish

    by ccadmin
    Read more

    SynPURE DTM Finish

    SynPURE DTM is a single component, high solids, low VOC, modified alkyd finish. It is Direct to the metal coating which is replaced by multi-coat systems.

    Category:
  • SynPURE Finish 1000 Series-Heavy Duty

    by ccadmin
    Read more

    SynPURE Finish 1000 Series-Heavy Duty

    SynPURE 1000 Series is a high build finish for Heavy-duty applications. Use as topcoat where corrosion protection required.

    Category:
  • SynPURE modified alkyd finish/SynPURE Premium Finish

    by ccadmin
    Read more

    SynPURE modified alkyd finish/SynPURE Premium Finish

    SynPURE modified alkyd Paints are recommended as topcoat where mild corrosion and chemical resistance required.It can be used for both exterior and interior surfaces mainly on mild steel, wooden, and suitably prepared masonry surfaces.

    Category:
  • SynPURE Primer 1000 Series-Heavy Duty

    by ccadmin
    Read more

    SynPURE Primer 1000 Series-Heavy Duty

    Heavy-duty primer formulated to provide long term protection of structural steel. It provides excellent adhesion and anti corrosive Properties.

    Category:
  • SynPURE Primer 77/37

    by ccadmin
    Read more

    SynPURE Primer 77/37

    SynPURE Primer series is a Solvent-borne modified alkyd primer. This product has an excellent balance of fast dry and tough film properties. It provides corrosion protection on structural steel in mildly to moderately corrosive environments.

    Category:
  • SynPURE Zinc Chrome Primer

    by ccadmin
    Read more

    SynPURE Zinc Chrome Primer

    SynPURE Chrome Primer is a Single pack, air drying, formulated with a special type of synthetic alkyd binder and micro zinc pigment to withstand high degree corrosion. It is for Mild Steel and non-ferrous surfaces providing hard and tough film.

    Category: